DC-0060S00-051-102
文件类型：PDF/Adobe Acrobat 文件大小：字节
更多搜索：DC -0060S 00-051-102
PART No:
DC-0060S00-051-102
Rev.: A Page:1/ 5
Approved/Date Checked/Date Written/Date
2.0 Pitch 6 Pin
Battery Connector
Product Specification
ZHANGWEI
2004-12-20
1.0 Scope : This specification covers the requirements for product performance and test methods of
GETWELL's Battery (Plug) Connectors of the part numbers specified as bellow.
Product shall be of the design, construction and physical dimensions specified in the applicable product
drawing.
2.0 Rating :
2.1 Voltage Rating : 50 V DC (REF)
2.2 Rated current : 0.5 AMPS (REF)
2.3 Temperature Range: -40 to +85 storage; -25 to +75 operating
3.0 Test Condition:
All tests shall be performed as bellow conditions unless otherwise specified.
3.1 Temperature range : +15 to +35
3.2 Humidity range: 25% to 85%
3.3 Atmospheric Pressure : 86kPa to 106 Kpa (860 to 1060 mber)
4.0 Test Methods and Requirements:
4.1 Examination of product:
Item Test Description Test Methods Requirement
4.1.1 Examination of
product (Outward
Appearance
Structure)
EIA 364-18
Shall be confirmed with eyes in
accordance with each drawing.
Shall be confirmed by using proper
measuring instruments.
1).Outward appearance shall be
good without such injurious problem
2).Structure shall be meet the design
and dimensional requirements of
drawing.
GETWELL TECH.(H.K.) LTD.
DOC. No.:
DC-0060S00-051-102 Rev.:A
Page:2/ 5
Approved/Date Checked/Date Written/Date
2.0 Pitch 6 Pin
Battery Connector
Product Specification
ZHANGWEI
2004-12-20
4.2 Electrical Performance:
Item Test Description Test Methods Requirement
4.2.1 Low Level Contact
Resistance
EIA 364-23A (or MIL-STD-1344A,
Method 3002.1, Test Condition B)
Subject mated contacts assembled in
housing to 20mV maximum open circuit
at 100 mA maximum
Measured from battery pack side to
main PCB side.
50 mOhms maximum
4.2.2 Insulation Resistance EIA 364-21B (or MIL-STD-202F,
Method 302, Test Condition B)
Unmated connector with 100 VDC
between adjacent contacts for 1 minute
100 MOHms minimum
4.2.3 Dielectric
Withstanding Voltage
EIA 364-20 (or MIL-STD-202F, Method
301, Test Condition B)
Test between adjacent contacts of
mated and unmated connector
assemblies.
500 V AC for one minute at sea level
1).No flashover or insulation
breakdown
2).Leakage current: 0.5mA Maximum.
4.3 MECHANICAL PERFORMANCE
4.3.1 Durability:
Battery side contacts
EIA 364-09B
Mate contacts at a rate of 10
cycles/minute to 5000 cycles
1 cycle insertion and withdrawal of
battery pack.
Contact resistance after 5000 cycles
100mOhms max.
Appearance: No damage
4.3.2 Durability:
PCB side contacts
Mate contacts at a rate of 10
cycles/minute to 50 cycles. 1 cycle
insertion and withdrawal of main PCB.
Contact resistance after 50 cycles
100mOhms max.
Appearance: No damage
4.3.3 Normal Force:
Battery side contacts
Measure normal force at contact point
Deflection 1.66mm
2.5~10N
4.3.4 Normal Force:
PCB side contacts
Measure normal force at contact point
Deflection 0.85mm
2.5~10N
GETWELL TECH.(H.K.) LTD.
DOC.
No.:DC-0060S00-051-10
2 Rev.:A
Page:3/ 5
Approved/Date Checked/Date Written/Date
2.0 Pitch 6 Pin
Battery Connector
Product Specification
ZHANGWEI
2004-12-20
Item Test Description Test Methods Requirement
4.3.5
Random Vibration
EIA 364-28B Test Condition V Test
Letter A, (or MIL-STD-202F, Method
214, Test Condition 1, Test Letter A)
5.35G's rms @ 50-2000Hz random
traversed in 15 minutes for 5 cycles.
<1us discontinuity
4.3.6
Contact Retention
Force
EIA 364-35
Shall be measured with TENSION
GAUGE or TENSION TESTER in same
direction.
1).Initial : 500 grams Min.
2).After test: 500 grams Min.
4.3.7
Physical Shock
EIA 364-27 Test Condition H (or
MIL-STD-202F, Method 214B)
50 G's Half-sine shock pulse for
3 shocks each X, Y, Z axes, total 18
shocks.
<1us discontinuity
4.4 ENVIRONMENTAL PERFORMANCE
4.4.1 Thermal Shock EIA 364-32B, Test Condition I, (or
MIL-202F, Method 107G Condition A.)
-40 for 30 minutes, +85 for 30
minutes Changeover<1 minutes. 1 hrs
recovery time, 24 cycles The last cycle
is to be finished at hot temperature.
Appearance: No damage.
Contact resistance: 100mOhms
Maximum.
4.4.5
Humidity
+50 @95% Humidity for 168 hours.
Appearance: No damage.
Contact resistance: 100mOhms
Maximum.
GETWELL TECH.(H.K.) LTD.
DOC. No.:
DC-0060S00-051-102 Rev.: A
Page:4/ 5
Approved/Date Checked/Date Written/Date
2.0 Pitch 6 Pin
Battery Connector
Product Specification
ZHANGWEI
2004-12-20
5.0 Test Sequence:
Test Group (a) Sample Groups
Test Item Test Description A B C D E F G H I J K L
4.1.1 Examination of product 1.10 1.4 1.10 1
4.2.1 Contact Resistance 2.7 2.3 2.7
4.2.2 Insulation Resistance 3.8
4.2.3 Dielectric Withstanding Voltage 4.9
4.3.1 Durability (battery side) 5
4.3.2 Durability (PCB side) 6
4.3.3 Normal Force: battery side cont. 3.8
4.3.4 Normal Force: PCB side cont. 4.9
4.3.6 Contact Retention Force 2
4.4.2
Humidity Note:
a. Samples shall be prepare in
accordance with applicable
manufacture's instructions and
shall be selected at random from
current production.
b. The numbers in the table indicate
sequence in which tests are
performed.
c. Precondition samples with 10
cycles durability.
d. All the tests shall be performed in
the sequence, indicated by the
number in the columns.
Each test groups shall consist of
minimum of eight connectors. A
minimum of 30 contacts shall be
selected and identified. Unless
otherwise specified, these contacts
shall be used for all measurements.
5 5 5 5
GETWELL TECH.(H.K.) LTD.
DOC.No.:
DC-0060S00-051-102 Rev.: A Page:5/ 5
Approved/Date Checked/Date Written/Date
GETWELL TECH.(H.K.)
2.0 Pitch 6 Pin
Battery Connector
Product Specification
ZHANGWEI
2004-12-20
LTD.6.1 Receptacle :Part Number
Description Drawing Number Remark
DC-006 2.0 Pitch 6 Pin Battery Connector
Getwell Tech. (H.K.) Co., Ltd
SPECIFICATIONS
5 Pin battery connector
DC-0060S00-051-102
1.136pcs/PVC吸塑
2.2560PCS/箱
3.箱子尺寸:315x195x115MM
Getwell Tech. (H.K.) Co., Ltd
型号:
物料号:
数量:
日期:
Notes:
Carton box:thickness=6mm
Unit=mm
Model Type:
Series No:
Model No:
Customer ref:
315190
115
5
·上一篇：DV摄影机Memory
·下一篇：数据仓库及数据挖掘技术在烟草CRM中的应用